113090 Euchner Safety Proximity Sensors

Product Details

• Weight
  0.73634308 lb
• Series
  CES-AZ evaluation
• Product Class
  Safety System
• Distance s, actuator
  min.4 mm (On mounting in non-metallic environment)
• Switching hysteresis
  min.1 mm (These values apply for the installation of the read head and the actuator in an aluminum profile 45 x 45 mm.)
• Assured operating distance Sao
  min.10 mm (These values apply for the installation of the read head and the actuator in an aluminum profile 45 x 45 mm.)
• Assured release distance Sar
  max.45 mm
• Operating distance
  20 mm (These values apply for the installation of the read head and the actuator in an aluminum profile 45 x 45 mm.)
• Mission time
  20 y (This value is dependent on the number of switching cycles and the switching current.)
• Number of switching cycles
  max.760000 1/Jahr
• Performance Level
  PL e (This value is dependent on the number of switching cycles and the switching current.)
• PFHD
  1.9 x 10⁻⁸ (This value is dependent on the number of switching cycles and the switching current.)
• Diagnostic Coverage (DC)
  99 %
• Category
  4 (This value is dependent on the number of switching cycles and the switching current.)
• Repeat accuracy R
  max.10 %
• LED indicator
  Status LED
• Input voltage
  15 ... UB V DC
• Output current
  max.20 mA
• Input current
  5 ... 8 ... 10 mA
• Output voltage
  0 ... 1 V DC
Discrepancy time
max.25 ms
Rated conditional short-circuit current
100 A
Rated impulse withstand voltage Uimp
4 kV
Utilization category acc. to EN 60947-5-1
230 V 2 A
Rated insulation voltage Ui
250 V
permissible resistance in feedback loop
max.600 Ω
Switching current
1 ... 300 mA
Type of output
Relay contacts, floating
Current via feedback loop
5 ... 8 ... 10 mA
Connection cross-section
0,25 ... 2,5 mm²
Degree of contamination (external, according to EN 60947-1)
2
EMC protection requirements
In acc. with EN 60947-5-3
Fusing
0,25 ... 8 A
Mechanical life
10 x 10⁶
Current consumption
150 mA (Without taking into account the load currents on the monitoring outputs)
Number of safety contacts
2 Relays with internally monitored contacts
Operating voltage DC
21 ... 24 ... 27 V DC Regulated, residual ripple < 5 %
Connection
Screw terminals
Dwell time
min.3 s (The dwell time is the time that the actuator must be inside or outside the operating distance.)
Number of read heads
Max. 4 read heads can be connected
Switching frequency
max.0,25 Hz (In case of monitoring with feedback loop, the actuators must remain outside the operating distance, e.g. with a door open, until the feedback circuit is closed.)
Reaction time
max.210 ms (Corresponds to the risk time according to EN 60947-5-3. This is the maximum switch-off delay for the safety outputs following removal of the actuator. In case of EMC interference in excess of the requirements in accordance with EN 60947-5-3
Mounting distance
min.10 mm (If several evaluation units are mounted side by side in a control cabinet without air circulation (e.g. fan), a minimum distance of 10 mm must be maintained between the evaluation units. The distance enables heat from the evaluation unit to di
Ambient temperature
-20 ... 55 °C
Atmospheric humidity
max.80 % rH
Mounting method
Mounting rail 35mm according to DIN EN 60715 TH35
Housing material
Plastic PA6.6
Ready delay
10 ... 12 s (After the operating voltage is switched on, the relay outputs are switched off and the door monitoring outputs are set LOW during the ready delay. For the visual indication of the delay, the green STATE LED flashes at a frequency of approx.
Degree of protection
IP20
Weight
0,25 kg